QCA Spa Jewel +3 Series El manual del propietario descargar pdf (Pagina 5)

Jewel Series Control

YOUR • QCA • SPA • EQUIPMENT

ML400 AX10

PN 53631 PN53584

Jewel + 3 Series Panel ML 400

Initial Start Up

Jets 1

When your spa is first powered up, it will go into Priming

Mode, indicated by “Pr”. Priming mode will last for 4

minutes and then the spa will begin to heat the spa and

maintain water temperature in the Standard Mode. You

can exit Priming mode early by pressing “Temp”.

Touch the “Jets 1” button once to turn pump 1 on or off,

and to shift between low and high speeds (if equipped). If

left running, the pump’s low speed will automatically turn

off after two hours, and the pump’s high speed will

automatically turn off after 15 minutes. The low speed of

pump 1 runs when the blower or any other pump is on. It

may also activate for at least two minutes every 30

minutes to detect the spa temperature (polling) and then to

heat to the set temperature if needed, depending upon

mode. When the low speed turns on automatically, it

cannot be deactivated from the panel; however, the high

speed may be started.

Temperature Control (80 ºF - 104 ºF)

The start-up temperature is set at 100ºF. The last

measured temperature is constantly displayed on the LCD.

Note that the last measured spa temperature displayed is

current only when the pump has been running for at least

two minutes.

Press the “Temp” button once to display the set

temperature. Pressing the “Temp” button a second time,

while it is still flashing, will cause the set temperature to

increase or decrease depending on what direction was last

chosen. Each press to follow will change the set

temperature in the same directions. If the opposite

direction is desired, release the pad and let the display

revert to the actual water temperature. Press the button to

display the set temperature, and again to make the

temperature change in the desired direction. After three

seconds, the LCD will automatically display the last

measured spa temperature.

Jets 2

Press the “Jets 2” button once to turn pump 2 on or off. If left

running, the pump will turn off after 15 minutes.

Light

Press the “Light” button to turn the light on and off. If left

on, the light automatically turns off after four hours.

Blower/Aux

If your system has a blower (and only one pump), but

your panel does not have a “Blower” button, use the

“Aux” button to control the blower. If left on, the blower

automatically turns off after 15 minutes. 1-speed

operation: on/off.

Mode

A button combination is used to switch between standard,

economy, and sleep modes. Press “Temp” followed by

“Light” to enter mode programming, press “Temp” to

cycle through to desired mode (LCD flashes until

confirmed), then press “Light” to confirm selection.

Preset Filter Cycles

The first filter cycle (“day”) begins six minutes after the

spa is energized. The second filter cycle (“night”) begins

12 hours later. Filter duration is programmable for 1-12

hours (F1-F12). The default filter time is two hours. To

program, press “Temp”, then “Jets 1.” Press “Temp” to

select the filter duration. Press “Jets 1” to select the

number of filter cycles. The display will show “

”

(both “day” and “night” cycles); “

” (“day” cycle

only); or “n” (“night” cycle only). Press “Temp” to

adjust, then press “Jets 1” to exit the programming mode.

For continuous filtration, use F12 and “

”.

Standard mode maintains the desired temperature. Not

that the last measured spa temperature displayed is current

only when the pump has been running for at least two

minutes. “

” will appear on the display momentarily

when you switch into Standard Mode.

Economy mode heats the spa to the set temperature only

during filter cycles. “

” will appear solid when the

temperature is not current and will alternate with the

temperature when the temperature is current.

Pressing “Jets1” while in Economy mode puts the spa in

Standard-In-Economy mode, (“

”) which operates

the same as Standard Mode, then reverts to Economy

Mode automatically after 1 hour. During this time,

pressing

”Temp” followed by “Light” will revert the mode to

Economy immediately.

Clean-up Cycle

When the pump or blower is turned on by a button

press, a clean-up cycle begins 30 minutes after the

pump or blower is turned off or times out. The

pump and the ozone generator** will run for one

hour.

Sleep Mode heats the spa to within 20 ºF of the set

temperature only during filter cycles. “

” will appear

on the display until mode is changed.

1 2 3 4 5 6 7 8 9 10 ... 13 14

Comentarios a estos manuales

Sin comentarios

QCA Spa Jewel +3 Series El manual del propietario Pagina 5

Comentarios a estos manuales

Relacionado con productos y manuales para Accesorios de piscina elevada QCA Spa Jewel +3 Series